\u00a9 2023 wikiHow, Inc. All rights reserved. Yes. If necessary, use a damp rag to provide increased grip. Just screw on a new tailpiece, reassemble the P-trap and you're done. Usually, there is a plastic washer on each side of the plastic ball. All Right Reserved. Once the plug is loosened, use your hands to unscrew the plug by twisting it in a counterclockwise direction until it is completely removed. If the pipe is too long, use a hacksaw or pipe cutter to. Add to Cart. 0:171:49How-To Remove Most-Common Bathtub Stoppers YouTubeYouTubeStart of suggested clipEnd of suggested clipBe sure to hold down the stopper base with your other hand like this while you are turning the knobMoreBe sure to hold down the stopper base with your other hand like this while you are turning the knob at. If your bathroom is poorly lit, please use a flashlight. Pop-ups can be operated by either pressing down on the drain cover or by lifting or pushing a rod behind the faucet. While holding the drain piece in place, fit the drain ring into the opening from above the sink, and thread the ring onto the drain tailpiece as far as you can by hand. House presentation (interior and exterior with aerial shots). The Delta sink stopper assembly is basically a simple lever. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. With the drain assembly removed, clean the sink thoroughly of debris and old plumber'sputty. The old drain has a plastic tail piece that is screwed on the metal drain body. You should be able to feel the tip of the pivot rod slide through the opening in the stopper linkage inside the drain assembly. When you need access to the drain pipe, simply unscrew and remove the stopper. Pour it into the drain in question. Check to make sure that the pop-up stopper opens and closes fully inside the drain opening. This article walked me through the process with simple, clear, descriptive steps and illustrations that are very accurate. Aaron's articles about plumbing on The Spruce span four years. You'll need to install a new drain stopper whenever you install a new sink. When the trip lever is engaged, the tub fills with water because the stopper has closed off the drain pipe. How To Remove Delta Bathroom Tub Stopper? Loosen this screw with a screwdriver or pliers to disengage the clevis so you can pull it off the pivot rod. We hope these tips will help you as you install a new drain and s. Remove the Drain Stopper Plug and Rocker Arm. Undo the screw holding the extension bar and lift out the drain stopper. Then, return to the sink and pull the stopper out. www.tubshroom.com.if(typeof ez_ad_units != 'undefined'){ez_ad_units.push([[728,90],'k2_builders_com-medrectangle-3','ezslot_5',115,'0','0'])};__ez_fad_position('div-gpt-ad-k2_builders_com-medrectangle-3-0'); 1:4912:21How to Install a Delta Pop-Up Sink Drain YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst is taking off that protective cover. This way, the pivot rod can go through the hole at the bottom of the drain stopper and move it up and down. Loosen this screw with a screwdriver or pliers to disengage the clevis so you can pull it off the pivot rod. It is for this reason that a broken stopper will cause the tub to slowly lose water. 0:024:40How To Replace a Rusty Sink Drain (HowToLou.com) YouTubeYouTubeStart of suggested clipEnd of suggested clipHi I'm them today I'm going to show you how to replace a rusty sink drain all you're going to be eatMoreHi I'm them today I'm going to show you how to replace a rusty sink drain all you're going to be eat is a new pop-up drain assembly from the hardware store this is what the drain looks like before we www.youtube.com. Before working under the sink, please unload the contents of the sink cabinet so that you can move under the sink more easily. Connect the vertical strap to the horizontal pivot rod by threading the spring clip onto the rod; one end of the clip attaches on each side of the strap. Push the pop-up drain tailpiece assembly up through the drain opening from under the sink as high as you can. 1. Apply a generous band of plumbers putty to the bottom of the flange on the new fitting. 0:030:50Most-Common Bathtub Stopper Removal Techniques YouTubeYouTube www.youtube.com. I never did this before, and do not have any plumbing. Use your hands or a set of pliers to squeeze the sides of the drain stopper and pull straight up and out of the drain. RP101631 also has this installation method. Behind the drain pipe under the sink is a horizontal rod that is connected to the lift rod by a strap. To install the new stopper, push the new sink drain into the opening and tighten the nut to secure it in place. You can probably reuse it. For tips about how to undo the tailpipe, keep reading! How To Change A Bathroom Sink Drain Assembly? Loosen this nut with pliers and remove it, then pull the pivot rod out of the tailpiece. We and our partners use cookies to Store and/or access information on a device. If the flange won't budge, wiggle the tailpiece until the seal breaks. Pull the rod and pivot ball from the drainpipe. This image may not be used by other entities without the express written consent of wikiHow, Inc.
\n<\/p>

\n<\/p><\/div>"}, {"smallUrl":"https:\/\/www.wikihow.com\/images\/thumb\/a\/a5\/Replace-a-Sink-Stopper-Step-23-Version-2.jpg\/v4-460px-Replace-a-Sink-Stopper-Step-23-Version-2.jpg","bigUrl":"\/images\/thumb\/a\/a5\/Replace-a-Sink-Stopper-Step-23-Version-2.jpg\/aid9621969-v4-728px-Replace-a-Sink-Stopper-Step-23-Version-2.jpg","smallWidth":460,"smallHeight":345,"bigWidth":728,"bigHeight":546,"licensing":"